Lumishore ECLIPSE SMX24 Surface Mount Underwater LED Light, Blue Light, 12V DC, 3,100 Fixture Lumens, 90° Beam, Marine Bronze Body

Overview

The Lumishore 010-04501-00 is a surface-mount underwater LED light that outputs blue light from a compact, low-profile housing. It runs on 12V DC only (10.5 to 15V) and carries an IP68 water-ingress rating for continuous underwater use.

On the outside, the light face is 70 mm (2.75 in) with a 17 mm (0.67 in) profile, which helps when space is tight on a transom or hull side. Light spread is a 90° beam, and the housing uses a marine bronze body with a borosilicate glass lens. It is rated for vessels up to 7.5 m (25 ft).

Key features

• 12V DC only (10.5 to 15V) with max current draw of 2.5A for power planning
• IP68-rated enclosure for underwater mounting
• Marine bronze body with a borosilicate glass lens
• 90° beam angle for a wide light pool off the stern or along the hull side
• 70 mm (2.75 in) face with a 17 mm (0.67 in) profile for tighter mounting areas
• 2 m (6 ft 6 in) cable as standard, with extension possible using proper gauge to control voltage drop
• Simple 2-wire installation for on/off control, with support for ECLIPSE Command Center control (zone control and dimming when connected)
• Isolation kit required when installing on conductive hull materials

Installation and setup

Mount the light on a flat section of transom or hull side where you can reach the inside of the hull for cable routing and sealing. For underwater illumination, placement about 100 to 300 mm (4 to 12 in) below the minimum load waterline keeps the beam in the water without putting the fixture too close to the surface.

The cable gland requires a recessed cut-out: a 13.5 mm (17/32 in) hole cut to a depth of about 15 mm so the light can sit flush. Use a marine sealant such as 3M 4200 or an equivalent, hand-tighten the mounting screws, and avoid power tools so the housing seats evenly. If you are installing three or more lights, even spacing of roughly 2.5 to 3 ft helps keep the light pool consistent.

Electrical and system integration

Plan the cable route before fastening the light and keep all connections waterproof. Each light should be individually fused with a 4A fuse, and wire sizing should follow ABYC guidance for voltage drop of 3% or less on critical circuits. The unit is 12V only, so it should not be tied into 24V systems without an appropriate, correctly sized DC-DC solution.

What’s included

• Surface-mount underwater LED light
• 3 marine bronze mounting screws

Maintenance and care

Check the light body and lens area regularly for marine growth and clean with a soft cloth or a soft bristled brush. Avoid abrasive pads and cleaners that contain solvents, acids, or alkalis. Do not use pressure washing or sandblasting equipment on the fixture.

Orders are processed within 2 business days, which includes verification, packing, and dispatch. Orders of $100 or more qualify for free shipping when eligible. For orders under $100, shipping costs are calculated at checkout based on destination, package weight, and selected service. International shipping is available for eligible products, and certain items may require additional handling, warehouse transfers, or may ship directly from the manufacturer, which can affect processing time.

Deliveries are handled by preferred carriers such as USPS, UPS, FedEx, DHL, and others depending on your location and selected service. Estimated delivery times are displayed at checkout and may vary due to customs processing, carrier delays, weather, postal disruptions, or other circumstances beyond our control. Once your order ships, you'll receive a confirmation email with tracking information. Tracking may take up to 24 hours to update on the carrier's website and is also available through your account when applicable.

We ship throughout the United States and to most international destinations for products eligible for international shipping. International orders may be subject to customs duties, taxes, brokerage charges, or other import fees, which are the customer's responsibility and are not included in the product or shipping price. PO Boxes are accepted only when shipping through USPS, and not all packages qualify for this option. If your order does not arrive within the estimated delivery window, please contact us at info@apollolighting.com or +1 (954) 375-0100 so we can assist with locating your package.

Learn more.

Returns may be requested within 30 days of receiving your order. Items must be unused, uninstalled, unaltered, and returned in their original packaging with all tags, packing materials, blank warranty cards, manuals, instructions, accessories, and included items. Certain products, including installed or used electronics, electrical components, lighting, consumables, custom or special-order items, cut-to-length products, safety equipment, and merchandise exposed to water or marine conditions, may not be eligible for return.

To request a return, sign in to your account and select the applicable order and items, and submit your request for review. Eligible unfulfilled items may also be submitted for cancellation within 1 hour of placing the order. Returns or cancellations are not considered approved until you receive confirmation from Apollo Lighting. Please do not ship or drop off merchandise before receiving return approval and instructions.

Customers are responsible for arranging and paying for return shipping unless the return is due to an error by Apollo Lighting or the item is verified as defective, damaged, or incorrect. Missing, damaged, defective, or incorrect items must be reported within 2 business days of delivery, and photos or other documentation may be required for review. If the issue is verified, Apollo Lighting may provide or reimburse return shipping and issue a replacement or refund depending on the circumstances. International customers are responsible for return shipping, duties, taxes, customs charges, brokerage fees, and other costs associated with an international return.

After your return is received and inspected, approved refunds are issued to the original payment method and may take 5-7 business days to appear after processing. Original shipping and handling charges are nonrefundable, and the value of any included free items that are not returned may be deducted from the refund. Apollo Lighting does not charge a standard restocking fee on eligible returns. Returns that are incomplete, damaged, installed, used, altered, improperly packaged, or otherwise do not meet the eligibility requirements may be refused. We recommend using a trackable and appropriately insured shipping service for all customer-arranged returns.

For assistance, contact info@apollolighting.com or call +1 (954) 375-0100.

Learn more.

Many products sold by Apollo Lighting include a manufacturer's warranty covering defects in materials or workmanship. Warranty terms vary by brand, product category, and model, so eligibility, coverage duration, exclusions, and available remedies are determined by the applicable manufacturer. We recommend reviewing the warranty information provided with your product before installation or use, especially for marine electronics, navigation equipment, lighting, electrical systems, pumps, safety equipment, and other specialized marine products.

If you need warranty service, the claim must follow the process established by the manufacturer, authorized service center, or designated warranty provider. You may be asked for proof of purchase, a serial number, product registration, photos, maintenance or installation records, or other documentation. Apollo Lighting does not determine or modify a manufacturer's warranty coverage or final claim decision, but we are happy to help provide purchase information and direct you to the appropriate manufacturer or warranty resource.

Keep your receipt, product documentation, serial number information, and original packaging when practical. Damage caused by normal wear, misuse, improper installation, insufficient maintenance, corrosion, impact, unauthorized modifications, electrical issues, or operation outside the manufacturer's specifications may not be covered. Warranty claims are separate from standard returns, so a product that has been installed, used, or exposed to marine conditions may no longer qualify for return while still remaining eligible for evaluation under the manufacturer's applicable warranty.

Learn more.